Minwax Vs Varathane

Yes, but no clear exterior finish will permanently protect wood against direct sun, snow, ice and rain. Be sure to check the finish annually to determine if it needs to be recoated. If the finish warrants, apply an additional coat of Helmsman® according to the label directions. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection or leave the area.

minwax vs varathane spar urethane

Both lacquer and polyurethane varnishes come at various prices, depending on the quality of their formula and name of the brand. Nevertheless, when applied as instructed and on objects that are not exposed to heat, polyurethane provides an overall much more durable and resilient finish than lacquer. If you have to apply more than one coat, you could end up spending much more time on your project if you opt for polyurethane. Lacquer is a broad term comprising a host of paint products. Before getting into the debate, I must say it’s hard to tell which product is best. Both lacquer and polyurethane come with pros and cons.


Which Is Better Oil Based Or Water Based Polyurethane?

I thought I was done, but lint settled in the “final ” coat overnight. These dressers came from the side of the road and were moved twice. Contrary to one of the posters above, I’ve had good success using colored minwax vs varathane spar urethane finishes when I’ve really needed to change the color of the wood for one reason or another. Mostly shellac with dye added, but have also used the colored polyurethanes as a base coat, top finished with clear.

  • It’s good to have both on hand so you can use the best option for that particular project.
  • I tried stains from both minwax and varathane from the local hardware stores.
  • Some of these links may be affiliate links which means that I will receive a small commission at no extra expense to you if you decide to purchase something.
  • I suppose it could be sanded but the sharp cabinet scraper is the best tool.
  • It only requires 30 minutes to dry and can be re-coated in about two hours.
  • I usually start with 600 grit–occasionally 400 if it has lots of problems.
  • Hopefully you now know the difference between spar marine varnish and spar urethane.
  • They could also give you inputs and techniques with regard to the application of either spar urethane or polyurethane.
  • Good marine spars include Epifanes Gloss, Pettit Captain’s, and Interlux Schooner.
  • A protective top coat prevents dirt, dust, water, oil, grease, etc. from penetrating into the wood.

This oil-based spray polyurethane will cause your indoor wooden surfaces to remain beautiful for longer due to the durability of this coating. You can use this product to protect all kinds of wooden furniture and surfaces in order to achieve a hard, clear, and semi-gloss finish. This product is quick to dry and can be applied to both finished and unfinished wooden surfaces, provided that they are based indoors.

Resists Uv Light

You’ll find polyurethane in paints as it provides a shiny, smooth finish. Whatever your preference, both of these brands are well respected and can give you the wooden finishing results you’re after. On the whole, Minwax products are significantly cheaper than Varathane finishes.

homemakerguide.com homemakerguide.com homemakerguide.com

A nice, thick coat of polyurethane is one of the best things you can do to improve the appearance and longevity of any wooden item. With one cheap and relatively easy step, you create a pleasing shine while also protecting the item from moisture. This is a generic term used for topcoats consisting of a higher ratio of solids. This product is perfect for raw wood and particularly suitable to use on exterior wood including garden furniture, fences, sheds, and decking.

The Why & How Of Woodworking

If you already know you want a fairly thick finish, then you should consider using a brush. But I don’t usually like a real thick film so 3-4 coats wiped on is usually a good compromise for me. And I would only sand after the second coat and every coat thereafter. Sand very lightly with 320 grit or higher just to knock down any surface nubs. Now if you should be able to get all the varnish off without damaging the paint, you’re best bet is to get away from oil-based finishes all together. Instead, switch to a water-based outdoor finish like General Finishes 450.

However, many other varnishes can be recoated in the same time, so take that name with a grain of salt. Cabot makes another spar varnish, at a lower price than the Epifanes varnish listed above. The manufacturer doesn’t mention what type of oil is used in their literature, but based upon the price, I’d say it’s probably linseed oil. Nevertheless, this varnish provides an excellent finish for both indoor and outdoor uses. It is UV protected, and being a spar varnish it is designed to be flexible and handle the effects of weather.

Interior finishes are relatively high in resin content and low in oil content, which creates a nice hard finish, but leaves little flexibility and penetration. Without the resin, you’re left with an extremely soft finish that may not hold up to traffic and wear. So, for an exterior wood finishing solution, we turned to boat makers and their years of experience in caring for wooden elements with the harshest exposures in the world.

minwax vs varathane spar urethane

It can be used with a variety of materials, including both water- and oil-based polyurethanes, and simply needs to be cleaned accordingly after each use. The sprayer also includes three brass spray tips to allow for even greater precision. Thus, you will be better off with a water-based polyurethane for lighter woods, whereas oil-based is great for enhancing the color of a darker wood. However, this also means that water-based polyurethanes are not as durable or as long-lasting as their oil-based counterparts. Polyurethane coatings became popular in the middle of the 20th century. They come in liquid form, and the main idea and reason for their applying are to protect the wooden surface.

Spar Urethane Vs Polyurethane: Difference

I would probably go for what I like to call the “bulletproof” finish. A pre-coat of CPES followed by as many coats as you want of Epifanes. This is a very protective film finish that should last a good long time. In all liklihood though, this finish will yellow a bit with time since the product is oil-based.

minwax vs varathane spar urethane

It gives a glossy finish and is non- yellowing when used on light colored surfaces. However, it take very long to dry it works best on natural wood. As a side note, check these woodworking designs and projects that I recommend by clicking here. I’ll discuss on how a Minwax finish compares to a Varathane finish. I’ll then dive into their use, durability, and the pros and cons of both. Rick Dennington It doesn’t matter what you use for outdoor furniture.

This means there’s a long time that dust could land on the project and dry in the finish. Any dust specs will need to be sanded out before applying the next coat. It’s resistant to water which makes it a great choice for protecting wood projects that will come in contact with moisture like kitchen cabinets and bathroom vanities. It’s also resistant to oil, grease, and other solvents. What I do understand, is when Wikipedia says polyurethane finishes for wood are “typically hard, abrasion-resistant, and durable coatings”. Which is another way of saying polyurethane is a protective top coat for wood.

Perhaps it’s not a surprise that there are other paint products you could consider. This product is often employed in treating weathered wood because it absorbs into the surface. Through absorption, lacquer forms a stronger bond with the wood that is harder to break. Speaking of brush strokes, you can avoid them altogether if you use lacquer because itcan be applied with a paint sprayer. On the bright side, polyurethane adheres well to most surfaces and can be applied over oil-based coats.

While shopping for water-based spar urethane, these two are the first products that come to mind. Although you might find both of these products similar at first, they are not. Therefore, we have brought you a comprehensive guide to help you make the right decision. Your finish should overtake the look of the wood itself, but instead enhance it.

minwax vs varathane spar urethane

I would need to re-read but I think there are one or two more. The first thing that you should know about spar urethane is that it features low levels of odor and toxicity. Therefore, it is the best choice for your requirements in case that you have allergy issues or if you want to protect the environment altogether. Have in mind that spar urethane tends to be more expensive than polyurethane and its quality is less consistent depending on the brand, of course. Obviously the time between stain and varnish application will be a factor. But if you didn’t experience major problems with beading of the waterbased poly as you were applying it I think you’re OK.

What Is Urethane Used For?

It was tougher to pick Recommended coatings at the two-year mark, as most wood finishes aren’t intended to go that long without maintenance. One-part varnishes that earned PSs recommendation this go-round were rated Fair for coating integrity and had no Poor ratings. Recommended two-part systems rated Good or better for coating integrity with no Poor ratings.

I was very impressed with this product and it’s ability to protect my wood items from sun and weather. The smell wasn’t too bad at all and it’s easy to apply to what you need to use it on. It doesn’t take much of this product when using it either which I love. [This review was collected as part of a promotion.] I love the shine that the Spar Urethane from Minwax provides for all my woodworking projects!

Source: homemakerguide.com